Refrigerator Filters
  • Whole House Filtration
  • Air Filters
  • Water Filters
  • How to Install a Whole House Water Filter

    November 09, 2026 10 min read

    A whole house water filter is installed on the main cold-water line after the main shutoff valve and before the water heater; on well water, it goes after the pressure tank. The DIY outline is short: shut off the water and relieve pressure, cut the pipe, fit shutoff valves and a bypass, connect INLET and OUTLET, mount the housing level, then flush and check for leaks. Some makers require a licensed plumber and local plumbing code always applies, so read your manual first; Table 2 shows what each maker says.

    Explore

    Shop Whole House Filter Systems

    Planning a DIY install? Compare whole house systems, then check each one's manual for its location rule and pressure limits before you buy fittings.

    Where to Install a Whole House Water Filter

    A whole house water filter is installed where the main cold-water line enters the home, after the main shutoff valve and ahead of the water heater. Point-of-entry systems are typically installed as water comes into a home and treat all the water in it, according to the Vermont Department of Health's residential water treatment guidance. If you're still choosing a water filter system for home use, check its manual's location rule before you buy fittings.

    Each maker sets its own location rule and limits. Table 1 puts them side by side, and your system's manual takes precedence over any table.

    Table 1. Where Each Maker Says to Install It, and Its Limits

    Maker / system Location rule Pressure Temperature
    Aquasana EQ-1000 Main line entry, before the water heater; upright; cold water only 20–100 psi 40–90 °F
    iSpring whole house Dry, level, frost-free, out of direct sunlight; cold water 25–80 psi (warranty: 45–80 psi) 40–100 °F
    Pentair PC600-P / PC1000-P Close to the supply inlet, upstream of all plumbing except outside pipes; well: after the pressure tank; booster pump: after the pump 20–125 psi 36–120 °F
    Culligan HF-150A After the water meter or pressure tank; out of sunlight; 1-1/2 inches of clearance below the housing 30–125 psi 40–100 °F
    Pentek Big Blue housing Protect from freezing Max 100 psi (#10) / 90 psi (#20) Max 100 °F

    Where a whole house water filter goes: main shutoff valve, then the filter on the main cold line, then the water heater; on a well, after the pressure tank.

    On the main cold line after the shutoff valve

    A whole house filter belongs on the main cold-water line, after the main shutoff valve, so you can turn off the supply to work on it. Pentair says to install its PC600-P and PC1000-P close to the water supply inlet, upstream of all plumbing except outside pipes. Culligan says to install the HF-150A after the water meter or pressure tank, on a 1/2-inch or 3/4-inch main line.

    Before the water heater

    A whole house filter goes before the water heater, because Aquasana says the EQ-1000 is installed where the main line enters the home, "prior to your water heater." Every maker in Table 1 rates its system for cold water only.

    Well water: after the pressure tank

    On a private well, the whole house filter goes after the pressure tank, according to Pentair and Culligan. Pentair adds that a system on a line with a booster pump goes after the pump.

    Dry, level, frost-free and in reach for cartridge changes

    The install spot for a whole house filter should be dry, level, protected from freezing and out of direct sunlight, as iSpring and Culligan state. Leave room below the housing to remove the sump: Culligan asks for 1-1/2 inches, and Aquasana asks for 50 inches of height for the EQ-1000. Once you know the spot, compare home water filter options against its space and limits.

    DIY or Plumber: Can You Install It Yourself?

    Whether you can install a whole house filter yourself depends on your maker's terms and your local plumbing code. Aquasana ties the EQ-1000 warranty to a licensed plumber, while iSpring says its system may need a licensed professional. Table 2 shows each maker's statement.

    Table 2. What the Makers Say About DIY, Codes and Plumbers

    Maker Statement Source
    Aquasana EQ-1000 Must comply with state and local laws and plumbing codes; a licensed plumber installs it to validate the warranty EQ-1000 install guide
    iSpring Follow all local plumbing and building codes; may need a licensed professional iSpring manual
    Pentair PC600-P Check plumbing, building and electrical codes; consult a licensed electrician about grounding in metal plumbing Pentair manual 4006016
    Culligan HF-150A Comply with state and local laws; fit a jumper wire if the pipes ground electrical systems HF-150A instructions

    What the makers say about DIY

    No maker in Table 2 says a whole house filter install is always a DIY job. iSpring says its system "may need to be installed by a licensed professional."

    When to call a licensed plumber

    Call a licensed plumber for a whole house filter when your maker's warranty requires one or when the job is beyond your skills. Ask a licensed electrician about grounding, as Pentair advises, if your home has metal water pipes.

    Local code, permits and your warranty

    Local plumbing code governs a whole house filter install, so check it with your permit office or a licensed plumber before you start. Aquasana, iSpring, Pentair and Culligan all say to follow state and local codes.

    Fittings, Pipe Types and Tools to Gather

    The fittings for a whole house filter depend on your pipe: PEX, copper and CPVC can take push-fit fittings, while galvanized pipe needs galvanized fittings. Table 3 lists what SharkBite and the filter makers say.

    Table 3. Pipe Types and Fittings by Source

    Item What the source says Source
    Push-fit (SharkBite Max brass) Fits PEX, copper, CPVC, PE-RT and HDPE; cut square, deburr copper and CPVC, mark insertion depth; not directly on galvanized pipe; permanent connection SharkBite pocket guide
    Copper pipe types K, L and M hard-drawn SharkBite FAQ
    Bypass loop pipe L-type copper iSpring
    Copper or galvanized connections Compression fittings for copper (BF-34 kit); galvanized fittings for galvanized pipe Culligan HF-150A
    Thread sealing (Aquasana) Teflon tape, no more than seven layers, two to three threads exposed; no pipe dope Aquasana EQ-1000
    Thread sealing (Pentair) Plumber's tape and/or thread-seal paste; do not overtighten Pentair PC600-P

    PEX, copper and CPVC: what push-fit fittings connect to

    SharkBite Max brass push-to-connect fittings join PEX, copper, CPVC, PE-RT and HDPE pipe, but not galvanized pipe directly. SharkBite says to cut the pipe square, deburr copper and CPVC, mark the insertion depth and push until the mark meets the release collar. SharkBite calls brass push fittings permanent connections and notes that "local code varies."

    Thread tape and sealant: follow your maker

    Thread tape rules for a whole house filter differ by maker, so follow your manual. Aquasana allows no more than seven layers of Teflon tape with two to three threads exposed, and says pipe dope voids the warranty. Pentair accepts plumber's tape and/or thread-seal paste, and Culligan says to wrap Teflon tape clockwise.

    Shutoff valves and a bypass loop

    Shutoff valves and a bypass loop let you isolate a whole house filter and keep water flowing while you service it. iSpring says a three-valve bypass and loop may be installed using L-type copper. Pentair's PC600-P ships with a pre-assembled bypass valve, while Culligan's HF-150A instructions describe no bypass.

    Tools and parts checklist

    The parts list for a whole house filter install comes from your system's manual, plus the fittings for your pipe type. Aquasana says PEX, clamps and mounting screws for the EQ-1000 are bought separately. Gather these before you start:

    • The filter housing or system, with its mounting bracket
    • Shutoff valves (ball valves) and, if used, bypass valves
    • Fittings for your pipe: push-fit, compression or galvanized
    • Teflon (PTFE) tape or the sealant your maker names
    • Pipe cutter, deburring tool and pipe hangers

    How to Install a Whole House Water Filter Step by Step

    To install a whole house water filter, shut off the water, cut the main cold line, fit valves, connect INLET and OUTLET, mount the housing level and set the cartridges.

    Six steps to install a whole house water filter: shut off and relieve pressure, cut the pipe square, fit valves and bypass, connect inlet and outlet, mount level, flush and check for leaks.

    1. Read your manual and pre-flush new cartridges if your maker says to (Aquasana: 15 minutes by garden hose).
    2. Shut off the main water supply and open a faucet to relieve pressure.
    3. Mark and cut the pipe square, then deburr copper or CPVC.
    4. Fit shutoff valves and, if you use one, the bypass loop.
    5. Connect the supply side to INLET and the house side to OUTLET.
    6. Mount the housing level on its bracket and support the pipe with hangers.
    7. Tighten each sump the way your maker says.
    8. Load the cartridges in your maker's order.

    Shut off the water and relieve pressure

    Before you cut into the main line, shut off the water supply and open fixtures to relieve the pressure, as iSpring instructs. iSpring also says to turn off electricity to the water heater during its install. For anything else about the water heater, follow the water heater's own manual.

    Cut the pipe and fit the valves and bypass

    Cut the main line square and deburr copper or CPVC before you fit push-fit valves, as SharkBite instructs. If you add a bypass loop, iSpring says to build it from L-type copper, not M.

    Mount the housing and connect inlet and outlet

    Mount the whole house filter housing level on its bracket and connect the supply to INLET and the house side to OUTLET. The Big Blue 20 manual says to attach the mounting bracket to the cap before making the connections, and to lubricate the O-ring with silicone grease, such as a water filter O-ring lubricant. Culligan says to hand-tighten the HF-150A sump only, while Pentair says to hand-tighten and then lightly snug with the wrench.

    Don't overtighten any fitting on a whole house filter. Aquasana says "Do not over tighten fittings," and Pentair gives the same warning.

    Set the cartridge order: sediment first, then carbon

    In iSpring's whole house system, the sediment cartridge goes first and the carbon block second, and the bracket can be flipped as long as that order is kept. Pentair leaves the sediment position to the installer: a pre-filter on well water and a post-filter on city water. Follow your maker; a whole house sediment water filter cartridge fits only the housing size it's made for.

    Keep a spare water filter replacement cartridge that matches the one your system shipped with.

    Flush, Leak-Check and Start Up

    To start up a new whole house filter, open the supply slowly, release trapped air, flush for your maker's stated time and check every connection for leaks. Flush times range from 5 minutes to 15 minutes plus cycling, as Table 4 shows.

    Table 4. Start-Up Flush by Maker

    Maker Flush Notes
    Aquasana EQ-1000 15-minute hose pre-flush before plumbing in; then 5–10 minutes at the nearest faucet Surge flush 30 seconds on, 30 seconds off
    iSpring Nearest cold faucet until clear and air is purged Don't use a hot faucet; cloudiness can last a couple of days
    Pentair PC600-P 15 minutes at about a pencil-width stream, then off 1 minute / on 1 minute until clear Grey or cloudy water for 7–10 days
    Culligan HF-150A 5 minutes Open supply slowly; press the red relief button to release air

    Open the supply slowly and release trapped air

    Open the water supply slowly after installing a whole house filter, then release trapped air. Culligan says to press the red pressure-relief button on the HF-150A to let the air out. iSpring says to run the flush until the air is purged.

    Flush time by maker

    The start-up flush for a whole house filter runs from 5 minutes to 15 minutes plus cycling, depending on the maker. Culligan says 5 minutes and Aquasana says 5–10 minutes at the nearest faucet. Pentair says 15 minutes, then cycling off 1 minute and on 1 minute until the water runs clear.

    Check every connection for leaks

    Check every whole house filter connection for leaks after start-up, as Culligan's start-up steps instruct. Check again before you finish, and re-check after the first day of use.

    Expect cloudy water at first

    Cloudy or grey water right after a whole house filter install is expected by the makers, and it clears with flushing and use. iSpring says cloudiness from air can last a couple of days. Pentair says grey or cloudy water can last 7–10 days.

    After Installing: Bypass, Pressure and Water Heater

    After installing a whole house filter, learn your bypass, watch for pressure changes and remember the water heater still holds unfiltered water. Cartridge changes are covered in our separate replacement guide.

    Using the bypass during service

    A bypass lets water reach the house while the whole house filter is isolated for service. Pentair's bypass valve has two positions, In Service and Bypass. iSpring says a three-valve bypass and loop may be installed; follow its manual for which valve to turn.

    Low pressure after install

    Low water pressure after a whole house filter install is a reason to check your system against its maker's limits. iSpring's warranty range needs at least 45 psi (30 psi with a booster pump) and no more than 80 psi.

    The water heater still holds unfiltered water

    The water heater still holds unfiltered water right after a whole house filter install, iSpring says. According to iSpring, that raw water is replaced in about 2–3 days of normal use.

    💡 Editor's Pick

    Housing already in place? Match the right sediment and carbon cartridges to your housing size with the Whole House Cartridge Filter Finder.

    Find My Whole House Filter →

    Frequently Asked Questions

    Can I install a whole house water filter myself?

    You may be able to install a whole house water filter yourself, but it depends on your maker and local plumbing code. iSpring says its system may need a licensed professional, and Aquasana ties the EQ-1000 warranty to a licensed plumber. Check your manual and local code before cutting the main line.

    Do I need a plumber to install a whole house water filter?

    You need a plumber for a whole house water filter if your maker's warranty requires one, like Aquasana's EQ-1000. Every maker in Table 2 says to follow state and local codes. Ask your permit office or a licensed plumber whether a permit or licensed installer is required where you live.

    Does a whole house water filter go before or after the water heater?

    A whole house water filter goes before the water heater, on the main cold-water line. Aquasana says the EQ-1000 goes where the main line enters, "prior to your water heater." On a well, it also goes after the pressure tank.

    Do I need a bypass valve for a whole house filter?

    A bypass valve isn't required by every maker, but it lets water reach the house while the whole house filter is serviced. iSpring says a three-valve bypass loop may be installed, and Pentair's PC600-P ships with one pre-assembled. Culligan's HF-150A instructions describe no bypass.

    How long does it take to install a whole house filter?

    The time to install a whole house filter depends on your plumbing, but allow time for the flush and a leak check. The makers' start-up flushes alone run from 5 minutes to 15 minutes plus cycling.

    Can I install a whole house water filter in a mobile home or apartment?

    Whether a whole house water filter can go in a mobile home or apartment depends on your manual, your landlord and local code. The makers' location rules still apply: main cold line, after the shutoff, before the water heater. In a rental, get the landlord's permission before cutting any pipe.


    Sources

    • Vermont Department of Health, Residential Drinking Water Treatment
    • Aquasana: EQ-1000 installation instructions
    • iSpring: whole house filter user manual
    • Pentair: PC600-P / PC1000-P system manual 4006016
    • Pentair Pentek: Big Blue housings spec sheet 310053; Big Blue 20 manual
    • Culligan: HF-150A installation and operating instructions
    • SharkBite: push-to-connect installer pocket guide 2024; push-to-connect fittings FAQ