Refrigerator Filters
  • Whole House Filtration
  • Air Filters
  • Water Filters
  • Does Reverse Osmosis Remove Microplastics?

    November 04, 2026 7 min read

    Reverse osmosis is expected to block microplastics, because an RO membrane is a dense film that rejects dissolved ions, but no NSF/ANSI 58 claim covers microplastics and no source we reviewed publishes a household removal rate. Plastic parts that sit after the membrane, such as the tank, tubing and post-filter, can also touch the water before it reaches your glass. The WHO concluded in 2019 that microplastics in drinking water don't appear to pose a health risk at current levels.

    The practical step is simple: follow your maker's flush and change schedule for your reverse osmosis filters. This guide covers RO systems only; other filter types are covered separately.

    Explore

    Shop Under-Sink RO Systems

    Comparing RO systems? Check each one's NSF/ANSI 58 certification and ask the maker for any microplastic test data before you buy.

    Reverse Osmosis and Microplastics: What the Evidence Shows

    The evidence on reverse osmosis and microplastics points to likely blocking, not a measured household removal rate. Each source below says something useful, and each leaves a gap. Table 1 sets out both sides.

    Table 1. Evidence Ladder: What Each Source Says

    Source What it says What it does not say
    WHO, 2019 No apparent health risk at current levels; conventional treatment removes particles under 1 micrometre Any RO removal rate for homes
    Cherian et al., Polymers 2023 Tested three pour-through devices; notes microplastics reported in full-scale UF and RO plant effluent Did not test RO
    US Bureau of Reclamation manual RO membrane is a dense film with no pores Microplastic test results
    NSF/ANSI 58 TDS reduction is the required claim No microplastic claim listed

    What WHO says about microplastics in drinking water

    The WHO says microplastics in drinking water don't appear to pose a health risk at current levels, based on limited information. In the WHO's 2019 news release on microplastics in drinking water, it also says conventional drinking-water treatment can remove particles smaller than one micrometre. The WHO calls for standard measurement methods and more research on how well treatment works.

    Peer-reviewed point-of-use research and its RO gap

    The most-cited peer-reviewed point-of-use study, "Microplastic Removal from Drinking Water Using Point-of-Use Devices" (Cherian et al., Polymers, 2023), did not test reverse osmosis. It tested three pour-through devices that combine carbon, ion exchange and, in two cases, a membrane or microfiltration stage. The authors note that microplastics have been reported in the effluent of full-scale ultrafiltration and RO plants.

    What manufacturers claim and why it is not a study

    Manufacturer claims about RO and microplastics are marketing statements, not household studies. No standard or manufacturer we reviewed publishes a household RO removal rate for microplastics. If a seller quotes a percentage, ask for the test report behind it.

    Why an RO Membrane Should Block Plastic Particles

    An RO membrane should block plastic particles because it rejects dissolved ions, which are far smaller than a plastic particle. Table 2 compares the sizes and mechanisms that sources actually publish.

    Size comparison: microplastics are under 5 mm, while an RO membrane is a dense film that rejects dissolved ions.

    Table 2. Size and Mechanism Comparison

    Item Size or mechanism Source
    Microplastic Less than 5 mm long NOAA
    Particles the body is unlikely to absorb Larger than 150 micrometres WHO
    Microfiltration Nominal 0.1 µm US EPA
    Ultrafiltration Nominal 0.01 µm US EPA
    RO membrane Dense film, no pores; retains more than 95% of ions US Bureau of Reclamation
    Nanoplastics No verified RO data None found

    Microplastics are larger than the ions RO rejects

    Microplastics are plastic pieces less than five millimetres long, according to NOAA, and they are much larger than the dissolved ions an RO membrane rejects. The US Bureau of Reclamation's membrane manual says RO retains more than 95% of all ions.

    A dense film, not a sieve with holes

    An RO membrane is a dense film with no pores, according to the US Bureau of Reclamation. Water and small uncharged molecules pass through spaces in the polymer, while rejected material goes to the drain with the reject water. That's why a home water filter membrane for RO is described differently from microfiltration and ultrafiltration, which EPA rates at nominal 0.1 µm and 0.01 µm.

    Nanoplastics: what we can and cannot say

    Nanoplastics are smaller, nano-sized plastic particles, and we found no verified data on how well RO removes them. The WHO says data on the uptake of nano-sized particles is extremely limited.

    Where Plastic Can Re-Enter After the Membrane

    Plastic can touch RO water after the membrane, because the storage tank, tubing, post-carbon filter and faucet all sit downstream. No maker or standards body publishes shedding data that we could verify. Table 3 maps the water path from the manuals.

    RO water path from feed water through pre-filters, membrane, storage tank and post-carbon filter to the faucet, with the parts after the membrane marked.

    Table 3. Water Path and Where Plastic Parts Sit

    Point in the water path What the manuals show Microplastic data
    Pre-filters and housings Before the membrane; Pentek says drain a full tank to flush carbon fines None published
    Membrane housing Reject water goes to the drain None published
    Storage tank and tubing Watts: flush the tank three times after a membrane change None published
    Post-carbon polishing filter Pentek: flush 4–5 minutes after install None published
    Faucet iSpring: discard the first full tank None published

    Storage tank, tubing and post-carbon filter

    The storage tank, tubing and post-carbon polishing filter all sit after the RO membrane, so water touches them on its way to the faucet. The Watts RO-PURE manual installs the post-carbon filter after sanitizing the system. We aren't saying these parts shed plastic; the data simply isn't published.

    New cartridges and housings: flush as the maker says

    New RO cartridges and housings should be flushed exactly as the maker's manual says. The Pentek RO-3000 manual says to drain one full tank to flush carbon fines after a filter change, and to flush for 4 to 5 minutes after installing the post-filter. The Watts RO-PURE manual says to flush the tank three times after a membrane change and drink from the fourth.

    The iSpring RCC7 manual says to discard the first full tank and let the faucet trickle for at least 15 minutes at startup.

    What a household can actually do

    A household can reduce uncertainty about plastic in RO water by following the flush steps and change schedule in its manual.

    1. Flush every new cartridge and membrane as the manual says.
    2. Drain the first tank after a filter or membrane change if the manual calls for it.
    3. Replace filters on the maker's schedule.
    4. Ask the maker for any microplastic test data on its system.

    What RO Certification Covers and What It Does Not

    RO certification under NSF/ANSI 58 covers total dissolved solids (TDS) reduction, not microplastics. A certified system has proven the claims printed on its listing, nothing more. Table 4 shows what each label covers.

    Table 4. Certification Versus Claim

    Item What it covers Microplastics?
    NSF/ANSI 58 TDS reduction required; optional claims for listed contaminants Not listed
    EPA WaterSense RO NSF/ANSI 58 plus at least 75% TDS reduction Not covered
    A "99%" marketing claim Whatever the seller's own test measured Ask for the report

    NSF/ANSI 58 and the TDS claim

    NSF/ANSI 58 requires a TDS reduction claim for reverse osmosis systems and lists optional claims for specific contaminants. NSF's list of optional claims includes cysts, arsenic, nitrate, VOCs and others, but no microplastic claim. EPA WaterSense-labeled RO systems must be certified to NSF/ANSI 58 and reduce TDS by at least 75%.

    How to read a "99%" microplastic claim

    A "99%" microplastic claim on an RO system is the seller's own number unless it points to a published test report. No standard or manufacturer we reviewed publishes a household removal rate. Treat a percentage without a report as marketing.

    Questions to ask before you buy

    Before you buy an RO system for microplastics, ask the seller three questions about its claim.

    • Which test report backs the claim, and who ran it?
    • Which particle size range was tested?
    • Which test method was used, and was the whole system tested or just the membrane?
    💡 Editor's Pick

    Due for an RO filter change? Find replacement filters for your system, then flush each new cartridge the way your manual says.

    Shop RO Filters →

    Frequently Asked Questions

    Does reverse osmosis remove nanoplastics?

    We found no verified data on how well reverse osmosis removes nanoplastics. The WHO says data on nano-sized particles is extremely limited. An RO membrane is a dense film with no pores, so blocking is plausible, but no standard or manufacturer we reviewed publishes a household nanoplastic removal figure.

    Can an RO system add microplastics to my water?

    No maker or standards body publishes data showing that an RO system adds microplastics, and none shows it doesn't. The tank, tubing, post-carbon filter and faucet sit after the membrane. Flush new parts exactly as your manual says, such as draining the first full tank after a change.

    Are microplastics in drinking water harmful?

    The WHO said in 2019 that microplastics in drinking water don't appear to pose a health risk at current levels, based on limited information. It also said particles larger than 150 micrometres are not likely to be absorbed by the body. The WHO called for more research.

    Is reverse osmosis the best filter for microplastics?

    We can't call reverse osmosis the best filter for microplastics, because no source we reviewed publishes a household RO removal rate. The membrane's dense film is expected to block particles. Other filter types are covered in a separate guide, so this article doesn't compare them.

    Does RO remove PFAS and fluoride too?

    Whether RO removes PFAS or fluoride depends on the system's certified claims, and those topics have their own guides. NSF/ANSI 58 lists fluoride as an optional claim, so check the listing for your model. This article covers microplastics only.

    How do I reduce plastic exposure from my RO system?

    To reduce plastic exposure from an RO system, follow the flush steps and filter change schedule in your manual. Pentek, for example, says to flush 4 to 5 minutes after installing a post-filter. Ask the maker for any microplastic test data, and keep the faucet and tank clean as directed.


    Sources