Refrigerator Filters
  • Whole House Filtration
  • Air Filters
  • Water Filters
  • How to Replace Filters and the Membrane in an Under-Sink RO System (4-Stage and 5-Stage)

    November 04, 2026 10 min read

    To replace the filters in an under-sink RO system, close the feed-water valve and the tank valve, open the RO faucet to drain the pressure, swap the pre-filters, fit the post-carbon filter last and replace the membrane if it's due. Finish by flushing the system, letting the storage tank fill and checking every connection for leaks. Housings, quick-change heads, tubing and flush times differ by maker, so this guide sets the Watts RO-PURE, Pentek RO-3000 and RO-3500, and iSpring RCC7 steps side by side.

    Explore

    Shop RO Replacement Filters

    Match the part numbers in your manual, then have the new pre-filters, post-carbon filter and membrane ready before you shut off the water.

    Before You Start: Parts, Tools and Your Manual

    Before you start replacing RO filters, gather a matching replacement set, the right housing wrench, a bucket or towel and food-grade silicone grease, and keep your manual open. Table 1 lists each item and which maker calls for it. When to replace each stage is covered in a separate schedule guide, so this post sticks to the physical steps.

    Table 1. Parts and Tools to Have Ready

    Item Why Who calls for it
    Replacement set with identical specifications Parts must match the originals Watts
    Housing wrench Loosens filter housings and the membrane cap iSpring; Pentek (membrane housing only)
    Bucket or towel Catches water when housings open iSpring, Watts
    Needle-nose pliers, or pliers or scissors Grip and pull the old membrane Pentek; iSpring
    Food-grade silicone grease Coats housing O-rings Pentek (FDA-grade)
    Dish soap and a non-abrasive cloth Cleans the housings Pentek
    Safety glasses and household bleach Only if your manual has a sanitizing step Pentek, Watts

    Match the replacement set to your stages

    To match the replacement set to your RO stages, count the stages from the feed line: the pre-filters come first, then the membrane, then the post-carbon filter. Stage counts differ by brand, so check your manual rather than assuming what a 4-stage or 5-stage system contains. Watts says replacement parts must have identical specifications to the originals.

    If you're restocking, compare the part numbers in your manual against our RO water filters before you order. Matching the part number is the simplest way to meet the identical-specifications rule.

    Tools and supplies to have ready

    The tools and supplies to have ready for an RO filter change are a housing wrench, needle-nose pliers, a bucket or towel, food-grade silicone grease, dish soap and a non-abrasive cloth. iSpring calls for a filter housing wrench and a membrane housing wrench, while Pentek uses its housing wrench on the membrane housing only. Safety glasses and household bleach are needed only if your manual includes a sanitizing step.

    Why your own manual wins

    Your own RO manual wins because Watts, Pentek and iSpring each give different steps, tools, flush times and tightening rules. None of the three makers publishes a numeric torque for housings. The EPA's guide to maintaining your water filter says to follow the maintenance instructions exactly and to follow the manufacturer's instructions when you change a cartridge.

    Shut Off the Water and Release the Pressure

    To shut off an RO system and release the pressure, close the feed-water valve and the tank valve, then open the RO faucet until the water stops. Each maker words this step differently, as Table 2 shows. Always depressurize before you open a housing or pull a quick-connect tube.

    Four steps to shut off and depressurize an under-sink RO system before changing filters: ice maker line off, feed valve closed, tank valve closed, RO faucet open.

    Table 2. Shut Off and Depressurize by Maker

    Maker Shut off Depressurize Also
    Watts RO-PURE Turn off the Adapt-A-Valve Open the RO faucet to drain the storage tank Ice maker off first; towel under the module
    Pentek RO-3000 / RO-3500 Close the saddle valve Open the drinking water faucet until the tank is empty, then close it Ice maker off; close the valve at the 1/4-inch tee
    iSpring RCC7 Shut the cold water supply valve and the tank valve Open the RO faucet Bucket or towel underneath

    Close the feed valve and the tank valve

    Close the feed-water valve first, which is the Adapt-A-Valve on a Watts RO-PURE and the saddle valve on a Pentek RO-3000 or RO-3500. iSpring also says to shut the tank valve on the storage tank along with the cold water supply valve. With both closed, no new water reaches the stages while you work.

    Open the RO faucet to drain pressure

    Open the RO faucet to drain pressure from the system before you loosen any housing or fitting. Watts says to open the RO faucet to drain the storage tank, and Pentek says to open the drinking water faucet until the tank is empty, then close it. Watts adds that quick-connect tubing should be disconnected only after the system is depressurized.

    Keep a towel or bucket under the system, as Watts and iSpring advise. Some water will still be in the housings when they come off.

    Turn off the ice maker line if one is connected

    Turn off the ice maker line first if your RO system also feeds a refrigerator or ice maker, as both Watts and Pentek instruct. Pentek also says to close the shut-off valve at the 1/4-inch tee. After the job, Pentek says to wait 1 hour before turning the ice maker back on.

    Replace the Pre-Filters and Post-Carbon Filter

    To replace the pre-filters and post-carbon filter in an RO system, open each housing or quick-change head, swap the cartridge, and fit the post-carbon filter last. How each connection comes apart depends on the maker, as Table 3 shows. The membrane steps follow in the next section.

    Table 3. How Each Connection Comes Apart

    Connection How Maker
    Filter housing (pre-filters) Unscrew counterclockwise with the housing wrench; hand-tighten to reinstall iSpring; Pentek (hand-tightened only)
    Quick-change cartridge Lift the head up to 90°, press and hold the button, pull straight down; the new one clicks in Watts
    Membrane cap Pull the tubing off the quick-connect, then unscrew the cap counterclockwise with the membrane housing wrench iSpring
    Membrane housing Unscrew the middle housing, turn the locking device clockwise, pull the membrane tube with needle-nose pliers Pentek
    Quick-connect tubing (Watts) Push the collet squarely against the fitting while pulling the tube Watts
    Quick-connect tubing (iSpring) Remove the blue lock clip, hold the lock sleeve down, pull; reconnect to the 5/8-inch mark iSpring

    Housing-style systems: unscrew, swap, hand-tighten

    On a housing-style RO system, unscrew each housing counterclockwise with the housing wrench, swap the cartridge and hand-tighten the housing back on. iSpring says not to overtighten, and Pentek says its filter housings are hand-tightened only. Use the wrench to loosen, and use it to tighten only if your manual says so.

    Quick-change cartridges: press, pull, click

    Quick-change RO cartridges, like those on the Watts RO-PURE, come out with a press and a pull instead of a wrench. Watts says to lift the heads and housings up to 90°, press and hold the button on the valve head and pull the cartridge straight down. Push the new cartridge in until it clicks.

    Clean the housings and lubricate the O-rings

    Clean the housings and lubricate the O-rings each time you open a housing-style RO system. Pentek says to pull each O-ring from its groove, clean it, wash the housing with dish soap and lightly coat the O-ring with FDA-grade silicone grease. Before you close the housing, confirm the O-ring is back in its groove.

    Use a 100% food-grade silicone water filter O-ring lubricant in a thin, pea-sized coat, and never petroleum jelly or motor oil. Replace any O-ring that is flattened, cracked or stiff.

    If a filter housing leaks after you close it, Pentek says to depressurize, clean and regrease the O-ring, then reinstall the housing by hand.

    Order: pre-filters first, post-carbon last

    Replace the pre-filters first and the post-carbon filter last, so the polishing filter goes in after the stages upstream are done. Watts says not to replace the post-carbon filter until sanitizing is complete, while the pre-filters and membrane may be changed before sanitizing. If your post-carbon cartridge has a flow arrow, follow the arrow or your manual.

    Replace the Membrane: Housing, Tubing and Fittings

    To replace the membrane in an under-sink RO system, disconnect the tubing, open the membrane housing, pull out the old membrane, seat the new one and close the cap. Watts says the new membrane must have identical specifications to the old one. Whether it's due is a separate question, answered with a TDS test.

    Disconnect the tubing from the quick-connect fitting

    Disconnect the tubing from the quick-connect fitting only after the RO system is depressurized, as Watts instructs. On Watts fittings, push the collet squarely against the fitting while pulling the tube. On iSpring fittings, remove the blue lock clip, hold the lock sleeve down and pull the tube out.

    Watts says not to remove or cut the flow restrictor inside the red tube.

    Remove the old membrane and seat the new one

    Remove the old RO membrane with pliers once the housing is open, then seat the new membrane without squeezing it or touching it with bare hands. iSpring says to unscrew the membrane cap counterclockwise with the membrane housing wrench and use scissors or pliers for leverage. Pentek says to unscrew the middle housing, turn the locking device clockwise and pull the membrane tube with needle-nose pliers.

    Before you insert the new home water filter membrane, iSpring says to clean the housing with hot water and, optionally, scent-free dish soap. Pentek says to lubricate the cap threads, brine seal and membrane O-rings with the supplied lubricant, push the membrane straight down until flush and secure the locking device counterclockwise.

    Close the cap, check the O-ring and reconnect

    Close the membrane cap, check its O-ring and reconnect the tubing before you turn the water back on. iSpring says to hand-tighten the cap, then add a 1/4 to 1/2 turn with the wrench, and to replace the cap O-ring every 3 years.

    When reconnecting Watts tubing, the tube must be cut square and deburred, pushed to the tube stop and pulled to confirm it holds. On iSpring fittings, push the tube to the 5/8-inch mark, past the O-ring, and snap the blue lock clip back on.

    Sanitizing: what each maker says

    Sanitizing an RO system during a filter or membrane change is a manual-specific step, because Watts, Pentek, iSpring and Culligan each say something different. Watts sanitizes once a year with household bleach in the tank tube, and Pentek sanitizes at membrane changes with a measured bleach solution in each housing. iSpring gives no sanitizing procedure, and Culligan leaves sanitizing to a technician.

    There is no universal bleach amount, so use your manual's amount and wear safety glasses, as Pentek advises.

    Flush, Fill the Tank and Check for Leaks

    After replacing RO filters, flush the system, let the storage tank fill, drain the first tank and check every connection for leaks, using your maker's own numbers. Table 4 sets those numbers side by side. No single flush time fits every RO system.

    RO storage tank fill time after a filter change by maker: Watts RO-PURE about 3 to 6 hours, Pentek RO-3000 6 to 12 hours, iSpring RCC7 about 1.5 to 2.5 hours.

    Table 4. Flush, Fill and Leak Check by Maker

    Maker Flush Tank fill Leak check
    Watts RO-PURE After annual maintenance: flush the first full tank. After a membrane change: flush three tanks, drink the fourth About 3–6 hours Keep checking connections for 24 hours
    Pentek RO-3000 / RO-3500 Filter-only change: drain one full tank. Membrane change: faucet drip 30 minutes, then 3 more hours; flush the D-20 for 4–5 minutes 6–12 hours Recheck once the tank is pressurized; ice maker off 1 hour
    iSpring RCC7 Run the first three stages into a bucket until clear; faucet trickle at least 15 minutes; discard the first tank About 1.5–2.5 hours Reopen the feed valve slowly and inspect each connection
    APEC Essence (50 GPD) Check your manual About 1.7–3 hours Check your manual

    Flush the new pre-filters and post-carbon

    Flush the new pre-filters and post-carbon filter exactly as your manual describes before you drink the water. iSpring says to flush the first three stages into a bucket until the water runs clear, then let the faucet trickle for at least 15 minutes. Pentek says to install the D-20 post-polishing filter with the black gasket end facing up and flush it for 4 to 5 minutes.

    Let the tank fill and drain the first tank

    Let the storage tank fill completely after an RO filter change, then drain the first tank before drinking from the RO faucet. Watts says a tank takes about 3 to 6 hours to fill and to discard the first batch, while iSpring gives about 1.5 to 2.5 hours and also says to discard the first full tank. Pentek gives 6 to 12 hours, and APEC puts its Essence 50 GPD system at about 1.7 to 3 hours.

    After a membrane change, Watts says to flush three tanks and use the fourth for drinking. Pentek's membrane procedure locks the faucet open to drip for 30 minutes, then adds a second 3-hour flush, and dripping can take up to 2 hours to begin.

    Leak check now and again after 24 hours

    Check every RO connection for leaks as soon as the water is back on, and keep checking for 24 hours, as Watts advises. iSpring says to reopen the feed valve slowly and inspect each connection, and Pentek says to recheck for leaks once the tank is pressurized. Watts says to use Teflon tape only on the tank ball valve, at 7 to 12 turns, and not to overtighten fittings.

    💡 Editor's Pick

    Opening the housings? Give each O-ring a thin coat of food-grade silicone, like the Tier1 OR-LUBRICANT-LG, before you hand-tighten it back on.

    Shop O-Ring Lubricant →

    Frequently Asked Questions

    Can I replace RO filters myself?

    Yes, you can replace RO filters yourself if you follow your system's manual. Watts, Pentek and iSpring all publish homeowner steps: shut off the water, depressurize at the RO faucet, swap the cartridges, then flush and check for leaks using the maker's own numbers.

    Do I have to turn off the tank valve?

    Yes, iSpring says to shut the tank valve along with the cold water supply valve before changing RO filters. Watts and Pentek instead have you close the feed valve and open the RO faucet to drain the storage tank. Check your manual for which valves your system has.

    Do I change the post-carbon filter at the same time as the pre-filters?

    You can change the post-carbon filter in the same session as the pre-filters, but install it last. Watts says not to install the post-carbon filter until any sanitizing is finished. Intervals differ by stage, though: Pentek replaces the D-15 every 4 months and the D-20 every 12 months, so check your manual's schedule.

    Why is my RO water slow or cloudy after changing filters?

    An RO system isn't ready right after a filter change; it needs the maker's full flush and tank fill first. Pentek says dripping can take up to 2 hours to begin after a membrane change, and tanks take from about 1.5 hours (iSpring) to 12 hours (Pentek) to fill. If it continues, check your manual.

    How long before I can drink the water after a filter change?

    You can drink RO water after a filter change once the maker's flush is done and the first tank has been drained. iSpring says to discard the first full tank, Pentek drains one full tank after a filter-only change, and Watts drinks the fourth tank after a membrane change.

    Do I need a wrench to change RO filters?

    You need a wrench for housing-style RO systems but not for quick-change ones like the Watts RO-PURE. iSpring uses a filter housing wrench and a membrane housing wrench, and Pentek uses its wrench on the membrane housing. Pentek's filter housings are hand-tightened only.


    Sources

    • US EPA, Learn how to maintain your water filter
    • Watts: RO-PURE installation, operation and maintenance manual 642230
    • Pentair Pentek: RO-3000 / RO-3500 reverse osmosis IOM 146250
    • iSpring: RO system user manual (RCC7 family)
    • APEC Water: FAQ and countertop RO manual
    • Culligan: How to keep your water filtration system working properly
    • DiscountFilterStore.com: O-ring lubricant guide