November 17, 2026 10 min read
Frigidaire water filter reset: to reset the water filter on a Frigidaire refrigerator, press and hold the WATER FILTER button (labeled Reset Water Filter on some control panels) for 3 seconds after you install the new filter. On an in-door control display, the status next to the button changes to GOOD. On panels with a Reset Water Filter control, a tone sounds once the reset is done. The light does not clear on its own when you change the filter, so the reset is a separate step every time. Below are the steps by control layout, what to check when the light won't reset, and how long to flush the new filter.
The Frigidaire water filter light is a replacement reminder, not a sensor that tests the filter. Frigidaire's Use & Care manuals tie the reminder to time and water use, so the light does not measure water flow, water taste or water quality.
When the Frigidaire water filter light or status changes, the refrigerator is telling you the filter has reached its replacement point. How that looks depends on your control layout.
Table 1: What the Frigidaire water filter indicator shows
| Control layout | What you see | What it means |
|---|---|---|
| In-door control display | A status shown to the right of the WATER FILTER button | Resets to GOOD after the 3-second hold |
| Side door (dispenser) control display | REPLACE WATER FILTER light | Comes on every 6 months, or when the filter needs replacing |
| External dispenser display (FRFN291 guide) | Replace Water Filter light | Comes on every 6 months or after 120 gallons |
Sources: Frigidaire Use & Care Manual A17856503 (pages 19 and 20) and Frigidaire Use & Care Guide FRFN291 (pages 15 and 17).
The Frigidaire water filter light comes on every 6 months, or after 120 gallons of water have been dispensed, on the models covered by the manuals we checked. Heavy water use reaches 120 gallons sooner, so the light can come on before the 6-month mark. The light is how a Frigidaire refrigerator tells you when to replace the water filter.
The Frigidaire water filter light stays on after a filter change because the reminder has to be reset by hand. Frigidaire's manuals tell owners to press and hold the button to reset it after the filter has been replaced. Until you do, the reminder keeps showing, even with a brand-new filter in place. What turns the indicator light on is the 6-month or 120-gallon count, not a fault with the filter or the water. Some owners describe this as a red light on the water filter indicator; the manuals we checked describe a REPLACE WATER FILTER light and a GOOD status rather than colors, so go by the wording on your own control panel.
To reset the water filter light on a Frigidaire refrigerator, find the control that shows the filter status, then press and hold the water filter button for 3 seconds. The exact label and where it sits depend on your model's control layout.

Install the new Frigidaire water filter cartridge before you reset the water filter light, because the reset only restarts the reminder. Remove the old filter, make sure the new cartridge is the correct part number for your model and is installed correctly and fully seated in the filter housing, then reset. Our guide on how to replace the filter on a Frigidaire refrigerator covers finding the part number and the locking motion for each filter style.
In the Frigidaire manuals we checked, the water filter status appears on one of two controls: an in-door control display, or a side door control display that sits with the water dispenser. The FRFN291 guide lists both, one for models with an external dispenser and one for models with an internal dispenser.

If you are unsure which one you have, find your model number on the refrigerator's model and serial number label and open the Use & Care Manual for that model. The manual's control panel diagram names every button.
On every Frigidaire control layout in the manuals we checked, the water filter reset is a 3-second press and hold. Follow these steps after the new filter is locked in place:
Table 2: Frigidaire water filter reset by control layout
| Control layout | Button label | Hold time | How you know it worked | Manual |
|---|---|---|---|---|
| In-door control display | WATER FILTER | 3 seconds | Status resets to GOOD | A17856503, p. 19 |
| Side door control display | WATER FILTER | 3 seconds | The replace reminder clears | A17856503, p. 20 |
| Control panel with a Reset Water Filter control | Reset Water Filter | 3 seconds | A tone sounds once reset | A10883135, pp. 15–16 |
| External dispenser display (FRFN291 guide) | Water filter button | 3 seconds | The replace light resets | FRFN291, p. 14 |
When you reset the indicator correctly, a Frigidaire water filter reset shows GOOD next to the button on in-door displays, or a tone on panels with a Reset Water Filter control. If the status still shows a replacement reminder, or you heard no tone, go to the troubleshooting section below before pressing other buttons.
Frigidaire Gallery and Frigidaire Professional are series names, so the water filter reset depends on your exact model's control display, not on the series. Two Gallery refrigerators can have different panels, so start with the model number.
To reset the water filter light on a Frigidaire Gallery refrigerator, use the WATER FILTER or Reset Water Filter button on that model's control display. Find the model number on the model and serial number label, then check the control panel section of the Use & Care Manual for that model number. The manual shows where the button is and confirms the hold time.
Frigidaire's manuals we checked use a 3-second hold on every layout. If your Gallery model's manual gives different steps, follow the manual for your model.
To reset the water filter light on a Frigidaire Professional refrigerator, use the same approach: find the model number, then the water filter control in that model's manual. The button may be labeled WATER FILTER or Reset Water Filter, and every layout in the manuals we checked uses the same 3-second hold. Where the manual for your model differs, follow it.
On side-by-side and French door Frigidaire refrigerators, the water filter reset still depends on the control display, not the door style. Look for the WATER FILTER or Reset Water Filter button on the in-door display or the side door control display, and hold it for 3 seconds.
Some Frigidaire refrigerators use a touchscreen or menu display instead of a dedicated water filter button. The manuals we checked describe button controls only, so we can't give a verified menu path. Open the filter item in your display's menu exactly as your Use & Care Manual describes, and use the reset option it lists there.
When the Frigidaire water filter light won't reset, start with the two things the manuals specify: the right button and a full 3-second hold. Work through these checks in order before calling for service.

Table 3: Frigidaire water filter light won't reset: checks in order
| What you see | What to check | What to do |
|---|---|---|
| Light or status unchanged after pressing | Which button you pressed | Use WATER FILTER or Reset Water Filter, not AIR FILTER |
| Light unchanged after a quick press | How long you held it | Hold the button for the full 3 seconds |
| Light comes back or never clears | Whether the filter is fully seated | Reseat the filter, repeat the 3-second hold, then contact Frigidaire with your model number |
Frigidaire refrigerators that have both reminders use a separate AIR FILTER or Reset Air Filter button, so pressing it will not clear the water filter light. Read the label before you press, and if you also changed the air filter, reset it with its own button. For the air filter steps, see our guide to resetting the air filter light on a Frigidaire refrigerator.
A quick tap does not reset the Frigidaire water filter light; you need to hold the reset button for 3 seconds, as the manuals specify. Count to three while holding the button, then release it and check the status or listen for the tone.
If the Frigidaire water filter light stays on after a correct 3-second reset, check that the new filter is fully locked in, then try the reset once more. Our guide on how to replace the filter on a Frigidaire refrigerator shows the locking motion for each filter style. If the light still won't clear, contact Frigidaire support with the model number from your model and serial number label.
Flush a new Frigidaire water filter for about four minutes of dispensing, or about 1 full gallon on models covered by the FRFN291 guide, before you drink the water. The manuals give slightly different flush instructions, so follow the one for your model.

Table 4: Frigidaire flush and reminder interval by manual
| Manual | Flush after a new filter | Reminder interval |
|---|---|---|
| Use & Care Manual A17856503 | Dispense water for about four minutes | Every 6 months, or when replacement is needed |
| All About the Use & Care of Your Refrigerator A10883135 | Dispense water for about four minutes | Every 6 months, or after 120 gallons |
| Use & Care Guide FRFN291 | Run about 1 full gallon and discard it; the purge can take up to 4 minutes | Every 6 months, or after 120 gallons |
Two Frigidaire manuals, A17856503 and A10883135, say to keep dispensing water for about four minutes after installing a new filter. Dispense into a container and discard the water. Table 4 shows the instruction and the reminder interval from each manual side by side.
The Frigidaire FRFN291 Use & Care Guide says to run about 1 full gallon of water through the dispenser and discard it, and notes the purge can take up to 4 minutes. Follow the gallon figure if your model's manual uses it. When the reminder comes on again after 6 months or 120 gallons, replace the filter and repeat the 3-second reset. Shop Frigidaire replacement filters to have the next one ready. Frigidaire water filters we carry include ULTRAWF PureSource Ultra, WFCB PureSourcePlus, FPPWFU01 PurePour and WF2CB PureSource2. That completes the Frigidaire water filter reset.
No, the Frigidaire water filter light does not reset by itself after a filter change. Frigidaire's manuals tell owners to press and hold the water filter button after replacing the filter. Until you do, the replacement reminder stays on, even though the new filter is already working.
Hold the Frigidaire water filter reset button for 3 seconds. That is the hold time in every Frigidaire Use & Care manual we checked, whether the button is labeled WATER FILTER or Reset Water Filter. A shorter tap usually leaves the light on, so count to three before you let go.
No, the Frigidaire water filter and air filter have separate reset buttons. The air filter control is labeled AIR FILTER or Reset Air Filter. Reset each reminder with its own button after you replace that filter, and check the label before pressing.
A new Frigidaire water filter does not turn off the light because the reminder runs on time and water use, not on a filter sensor. The manuals set it to 6 months or 120 gallons. Press and hold the water filter button for 3 seconds to start the count again.
To turn off the water filter light on a Frigidaire refrigerator, press and hold the WATER FILTER or Reset Water Filter button for 3 seconds. That reset is the only way the manuals describe to clear the light. Replace the filter first if it is due, so the next reminder matches the real filter age.
The water filter reset button on a Frigidaire refrigerator is on the in-door control display or on the side door control display with the water dispenser. Which one depends on your model. The control panel diagram in your Use & Care Manual shows the exact spot.
Yes, Frigidaire refrigerators with a water filter reminder have a reset control for it, labeled WATER FILTER or Reset Water Filter in the manuals we checked. It sits on the in-door control display or the side door control display, depending on the model. It resets the water filter reminder only, not the whole refrigerator.
The Frigidaire manuals we checked describe the water filter reset only as a step after you install a new filter. Pressing and holding the button restarts the 6-month or 120-gallon reminder, so resetting it with the old filter still in place leaves you without a reminder for a filter that is already due.
Yes, reset the Frigidaire water filter light every time you change the filter. The manuals pair the reset with each replacement. Skipping it leaves the reminder on and the next reminder out of step with your real filter age.