November 18, 2026 8 min read
To test drinking water at home, start with your water source: city water customers read the annual water quality report from their utility, and private well owners test every year for total coliform bacteria, nitrates, total dissolved solids (TDS) and pH. A home test kit gives quick readings for things like pH, chlorine, hardness, iron and TDS. For bacteria, nitrates and lead, EPA and CDC point you to a state-certified drinking water laboratory. Below is what to test for, how to collect a sample, when a lab is the right choice, and how to read your results against EPA levels.
What you should test your drinking water for depends on where it comes from: a public water system already tests and reports on it, while a private well is tested only if you test it. Table 1 shows the starting point for each source.
Table 1: Drinking water testing by water source
| Water source | What to check | How often | Source |
|---|---|---|---|
| Public (city) water system | Your utility's annual Consumer Confidence Report | Every year (reports are due by July 1) | EPA |
| Private well | Total coliform bacteria, nitrates, TDS and pH | At least once a year | EPA, CDC |
| Either source | Any change in odor, color or taste | Right away | EPA |
If you have city water, start by reading your Consumer Confidence Report (CCR), the annual water quality report your water system must send each year by July 1. EPA requires community water systems to deliver it. If you can't find yours, call your local water supplier or look it up with EPA's CCR search tool. The report lists what the system tested for and what it found.
If you have a private well, you are responsible for testing it, because the rules that protect public drinking water systems do not apply to privately owned wells. EPA recommends testing a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH. CDC adds that you should test for other germs and chemicals of concern in your area, which your local health department can name.
Test your drinking water right away when something changes: a known water problem in your area, flooding or construction near your well, a well repair, or a new odor, color or taste that could signal water contamination. EPA also suggests testing a well more often if small children or older adults live in the home, or if someone is pregnant or nursing.
To test drinking water at home, choose a method that covers what you need to know, collect the sample exactly as the instructions say, then read and record the result. The method matters most, because no single home kit tests for everything.
Table 2: Home testing methods compared
| Method | What it measures | What it does not cover | Best for |
|---|---|---|---|
| Pro Products 2401 reagent kit | Hardness, iron, pH | Bacteria, lead, nitrates, PFAS | Quick hardness, iron and pH checks at the tap |
| Pro Products 2404 kit (includes a TDS meter) | Hardness, iron, pH, chlorine, TDS | Bacteria, lead, nitrates, PFAS | On-the-spot checks, and testing before and after a filter |
| State-certified drinking water laboratory | Health contaminants such as bacteria, nitrates and lead | Nothing you can read yourself at the tap | Annual well tests, lead and any health concern |
Choose a home kit for quick readings of pH, chlorine, hardness, iron or TDS, and a state-certified lab for bacteria, nitrates, lead and other health contaminants. Home options for DIY testing include test strips, reagent kits that change color, and a TDS meter. DiscountFilterStore.com carries water test kits such as the Pro Products 2404 kit, which adds chlorine and a TDS meter to the hardness, iron and pH tests in the Pro Products 2401 kit. Hardness is a reading in both kits; our guide on how to test for hard water explains that number.

Collect the drinking water sample exactly as your kit or lab instructions say, because the tap, the container and the timing all change the result of the testing process.

Run the test strips or kit as the instructions direct, compare the color or meter reading in good light, and write down the value, the unit, the date and which tap you sampled. Test strips and reagent tests both work by color: you match the sample to the reference color chart that comes with the kit, as the Pro Products 2401 and 2404 instructions describe. A TDS meter shows a number instead. Keeping a written record lets you compare this year's results with next year's.

A home test kit is for quick readings of the parameters it lists, while a state-certified lab is the route EPA and CDC point to for testing drinking water for health contaminants. Table 3 compares the two.
Table 3: Home kit vs state-certified lab
| Question | Home test kit | State-certified lab |
|---|---|---|
| What does it test? | Only the parameters on the box | The tests you order, including bacteria, nitrates and lead |
| Who reads the result? | You, against a color chart or meter | The lab, in a written report |
| When do you get results? | As the kit instructions state | As the lab states |
| Use it for | Taste, odor and treatment checks | Annual well tests and health concerns |
A home test kit can tell you the pH, chlorine, hardness, iron or TDS of your drinking water, but only the parameters it lists. The DiscountFilterStore.com page for the Pro Products 2401 kit says plainly that it does not test for bacteria, lead, nitrates or PFAS, and the 2404 kit lists only hardness, iron, pH, chlorine and TDS. Use a kit to check taste and treatment questions, not to rule out harmful contaminants.
Use a state-certified drinking water laboratory whenever you need to test for bacteria, nitrates, lead or any other health contaminant. EPA encourages individuals to contact a state-certified lab, and CDC tells well owners to use one. EPA does not test residential drinking water on request, so the lab is where you pay for the test.
Get your drinking water tested at a state-certified drinking water laboratory, which you can find through EPA's list of state certification programs or your state or local drinking water authority or health department. EPA publishes that list as a PDF on its laboratory certification page. You can also call EPA's Safe Drinking Water Hotline at 1-800-426-4791.
To read drinking water test results, find each parameter's number and unit, such as mg/L, and compare it with the EPA level for that parameter. Then note whether the EPA level is a health-based limit or a taste and appearance guideline. Table 4 lists the EPA levels for the most common home and well tests.
Table 4: EPA drinking water levels for common tests
| Parameter | EPA level | Type | Source |
|---|---|---|---|
| Nitrate (as nitrogen) | 10 mg/L | Health-based limit (MCL) | EPA primary standards |
| Total coliform bacteria (including E. coli) | Goal of zero | Health-based goal (MCLG) | EPA primary standards |
| pH | 6.5 to 8.5 | Taste and appearance guideline | EPA secondary standards |
| Total dissolved solids (TDS) | 500 mg/L | Taste and appearance guideline | EPA secondary standards |
EPA's health-based maximum contaminant level (MCL) for nitrate in drinking water is 10 mg/L, and its goal for total coliform bacteria, including E. coli, is zero. EPA notes that infants under 6 months who drink water with nitrate above the MCL could become seriously ill. These numbers come from the National Primary Drinking Water Regulations.
EPA's secondary drinking water standards set a pH range of 6.5 to 8.5 and a TDS level of 500 mg/L. These are guidelines for taste, odor and appearance, not federally enforceable limits. A reading outside them is a reason to look further, not a health verdict on its own.
If a drinking water result is out of range, contact your water utility if you have city water, or retest at a state-certified lab and call your health department if you have a well. Once a lab confirms the problem, choose a filtration system that targets that specific result. For well results, our guide to well water problems and solutions matches common problems to the right filter.
How often to test drinking water depends on the source: test a private well at least once a year, and read a city water system's new report every year.
Test private well water at least once a year for total coliform bacteria, nitrates, TDS and pH, and check the well every spring. CDC says to check your well every spring at a minimum, to make sure there are no mechanical problems. Test again right away after flooding, repairs or a change in taste, odor or color.
With city water, read your utility's new Consumer Confidence Report every year when it arrives by July 1. Test at home only for a specific concern. For lead from household plumbing, EPA says to contact your water utility to have your water tested.
Yes, you can test your drinking water yourself for parameters like pH, chlorine, hardness, iron and TDS with a home test kit. For bacteria, nitrates and lead, collect the sample yourself but send it to a state-certified drinking water laboratory, as EPA and CDC advise.
A home water test kit reads only the parameters it lists, so it cannot tell you whether drinking water is free of contaminants it does not test. EPA and CDC point to state-certified labs for health contaminants. Follow the kit instructions exactly for the most reliable reading.
Not all of them: the Pro Products 2401 and 2404 home test kits do not test for bacteria, lead, nitrates or PFAS. To test drinking water for coliform bacteria, use a state-certified lab. EPA recommends that test every year for private wells.
With city water, start with the annual Consumer Confidence Report, because your water system tests the water and reports the results there each year. Test at home for a specific concern, such as lead from your home's plumbing, and contact your water utility first.
Testing is the only sure way to know whether drinking water has harmful levels of lead, and EPA says to contact your water supplier or a certified lab to have it tested. EPA puts lead testing at $20 to $100. If lead is found, see whether a water filter removes lead.
No, a TDS meter is not enough to test drinking water on its own, because it reads total dissolved solids only, not bacteria, lead or nitrates. EPA's TDS guideline is 500 mg/L, a taste and appearance level. Pair a TDS reading with a state-certified lab test for health contaminants.
No, EPA does not test residential drinking water on request. It encourages you to contact a state-certified drinking water laboratory instead. City water is tested by your water system, which reports results in its annual Consumer Confidence Report.